| Author |
Message
|
| srinivas07438 |
 Posted: Wed Jun 26, 2013 1:17 am Post subject: setting channel authorization |
 |
|
Apprentice
Joined: 26 Jun 2013
Posts: 28
|
i issue the following command to block
i am using the windows
SET CHLAUTH('*') TYPE(ADDRESSMAP) ADDRESS('*') USERSRC(NOACCESS)
Please can anyone tell me what I am missing?
Last edited by srinivas07438 on Wed Jun 26, 2013 8:15 pm; edited 3 times in total |
|
| Back to top |
|
 |
| smdavies99 |
| Posted: Wed Jun 26, 2013 1:35 am Post subject: |
|
|
Jedi Council
Joined: 10 Feb 2003
Posts: 6076
Location: Somewhere over the Rainbow this side of Never-never land.
|
Perhaps you should attend some IBM training on the product. This would have enabled you to complete this task without posting here.
Hint...
This command can't be run directly from the command line. You need to be running an application that understands the command first.
I will leave you to work out what application it is for yourself. The IBM documentation even has a whole section on this application.
_________________
WMQ User since 1999
MQSI/WBI/WMB/'Thingy' User since 2002
Linux user since 1995
Every time you reinvent the wheel the more square it gets (anon). If in doubt think and investigate before you ask silly questions. |
|
| Back to top |
|
|
| srinivas07438 |
| Posted: Wed Jun 26, 2013 7:55 pm Post subject: |
|
|
Apprentice
Joined: 26 Jun 2013
Posts: 28
|
Tq
can i have the link please
I TRIED TO ALTER THE QUEU MANAGER BY EXECUTING COMMAND
ALTER QMGR CHLAUTH(ENABLED)
BUT NOT EXECUTED THE FOLLOWING IS SHOWING
ALTER QMGR CHLAUTH(ENABLED)
1 : ALTER QMGR CHLAUTH(ENABLED)
AMQ8405: Syntax error detected at or near end of command segment below:-
ALTER QMGR CHL
AMQ8427: Valid syntax for the MQSC command:
ALTER QMGR [ FORCE ]
[ ACCTINT( integer ) ] [ ACCTCONO( ENABLED | DISABLED ) ]
[ ACCTMQI( ON | OFF ) ] [ ACCTQ( NONE | ON | OFF ) ]
[ ACTIVREC( MSG | QUEUE | DISABLED ) ] [ AUTHOREV( ENABLED | DISABLED ) ]
[ CCSID( integer ) ] [ CHAD( ENABLED | DISABLED ) ]
[ CHADEV( ENABLED | DISABLED ) ] [ CHADEXIT( string ) ]
[ CHLEV( ENABLED | DISABLED | EXCEPTION ) ]
[ CLWLDATA( string ) ] [ CLWLEXIT( string ) ]
[ CLWLLEN( integer ) ] [ CLWLMRUC( integer ) ]
[ CLWLUSEQ( LOCAL | ANY ) ]
[ CMDEV( ENABLED | DISABLED | NODISPLAY ) ]
[ CONFIGEV( ENABLED | DISABLED ) ] [ DEADQ( string ) ]
[ DEFXMITQ( string ) ] [ DESCR( string ) ]
[ INHIBTEV( ENABLED | DISABLED ) ] [ IPADDRV( IPV4 | IPV6 ) ]
[ LOCALEV( ENABLED | DISABLED ) ] [ LOGGEREV( ENABLED | DISABLED ) ]
[ MARKINT( integer ) ] [ MAXHANDS( integer ) ]
[ MAXMSGL( integer ) ] [ MAXUMSGS( integer ) ]
[ MAXPROPL( NOLIMIT | integer ) ]
[ MONACLS( QMGR | OFF | LOW | MEDIUM | HIGH ) ]
[ MONCHL( NONE | OFF | LOW | MEDIUM | HIGH ) ]
[ MONQ( NONE | OFF | LOW | MEDIUM | HIGH ) ]
[ PARENT( string ) ] [ PERFMEV( ENABLED | DISABLED ) ]
[ PSMODE( ENABLED | DISABLED | COMPAT ) ]
[ PSNPRES( NORMAL | SAFE | DISCARD | KEEP ) ]
[ PSNPMSG( DISCARD | KEEP ) ] [ PSRTYCNT( integer ) ]
[ PSSYNCPT( YES | IFPER ) ] [ REMOTEEV( ENABLED | DISABLED ) ]
[ REPOS( string ) ] [ REPOSNL( string ) ]
[ ROUTEREC( MSG | QUEUE | DISABLED ) ] [ SCHINIT( MANUAL | QMGR ) ]
[ SCMDSERV( MANUAL | QMGR ) ] [ SSLCRLNL( string ) ]
[ SSLCRYP( string ) ] [ SSLFIPS( YES | NO ) ]
[ SSLKEYR( string ) ] [ SSLRKEYC( integer ) ]
[ SSLEV( ENABLED | DISABLED ) ]
[ STATACLS( QMGR | OFF | LOW | MEDIUM | HIGH ) ]
[ STATCHL( NONE | OFF | LOW | MEDIUM | HIGH ) ]
[ STATINT( integer ) ] [ STATMQI( ON | OFF ) ]
[ STATQ( NONE | ON | OFF ) ] [ STRSTPEV( ENABLED | DISABLED ) ]
[ TREELIFE( integer ) ] [ TRIGINT( integer ) ]
IN THIS WHICH ONE I HAVE TO CHANGE FOR THE
ALTER QMGR CHLAUTH(ENABLED)
Last edited by srinivas07438 on Wed Jun 26, 2013 9:12 pm; edited 1 time in total |
|
| Back to top |
|
|
| srinivas07438 |
| Posted: Wed Jun 26, 2013 9:15 pm Post subject: |
|
|
Apprentice
Joined: 26 Jun 2013
Posts: 28
|
i executed from the runmqsc control program and giving the response as
SET CHLAUTH('*') TYPE(ADDRESSMAP) ADDRESS('*') USERSRC(NOACCESS)
2 : SET CHLAUTH('*') TYPE(ADDRESSMAP) ADDRESS('*') USERSRC(NOACCESS)
AMQ8405: Syntax error detected at or near end of command segment below:-
S
AMQ8426: Valid MQSC commands are:
ALTER
CLEAR
DEFINE
DELETE
DISPLAY
END
PING
REFRESH
RESET
RESOLVE
RESUME
START
STOP
SUSPEND |
|
| Back to top |
|
|
| exerk |
| Posted: Wed Jun 26, 2013 10:04 pm Post subject: |
|
|
Jedi Council
Joined: 02 Nov 2006
Posts: 6339
|
Bear in mind that you can only execute SET CHLAUTH commands on WMQ V7.1 and above.
_________________
It's puzzling, I don't think I've ever seen anything quite like this before...and it's hard to soar like an eagle when you're surrounded by turkeys. |
|
| Back to top |
|
|
| srinivas07438 |
| Posted: Wed Jun 26, 2013 10:21 pm Post subject: |
|
|
Apprentice
Joined: 26 Jun 2013
Posts: 28
|
| tq every one i got the solution, actually i am using the version 7.0, so it is not working because the channel auth rules integrated in the version mqv7.1 onwards. |
|
| Back to top |
|
|
|
|
