| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Entry poing to AMQXCS2.dll |
« View previous topic :: View next topic » |
| Author |
Message
|
| greenears |
 Posted: Thu Jun 20, 2002 3:33 pm Post subject: Entry poing to AMQXCS2.dll |
 |
|
Newbie
Joined: 12 Jun 2002
Posts: 6
|
Hi
I recently upgraded my test machine from v 5.1 to v 5.2.1 (without CSDs). The upgrade was done without installing v 5.1 but using the "Update" option on v 5.2
We have a component created using MQSeries APIs. This component has been working fine with v 5.1. But registering this component against v 5.2.1 resulted in an error. Please also note that we have successfully converted two of our development machines to v 5.2 and the component works fine in these machines.
While registering, I am getting an error
"The procedure entry point @xtr_FNC_entry@8 could not be located in dynamic link library AMQXCS2.dll"
There is only one copy of AMQXCS2.dll in the entire system.
Any help is much appreciated.
Thanks |
|
| Back to top |
|
 |
| blane99 |
| Posted: Tue Jul 09, 2002 4:54 am Post subject: |
|
|
Apprentice
Joined: 12 Jun 2002
Posts: 41
|
I had similar problem installing 5.2.1 but different DLL. Solution was found in Microsoft knowledge base.
"The Procedure Entry Point ??_U@YAPAXI@Z Could Not Be Located in Msvcrt.dll" Error Message When You Start Windows (Q318730)
--------------------------------------------------------------------------------
The information in this article applies to:
Microsoft Windows NT Server version 4.0
Microsoft Windows NT Server version 4.0 , , Terminal Server Edition
Microsoft Windows NT Workstation version 4.0
SYMPTOMS
When you start your Windows NT 4.0-based computer, you may receive an error message similar to the following:
rpcss.exe
The procedure entry point ??_U@YAPAXI@Z could not be located in msvcrt.dll
-or-
When you try to start a program, you may receive an error message similar to the following:
Application .exe - Entry Point not Found
The procedure entry point ??_U@YAPAXI@Z could not be located in the Dynamic Link Library MSVCRT.DLL
CAUSE
This behavior may occur if you install a third-party program that replaces some of the Windows NT 4.0 dynamic-link library (DLL) files with those of a different version.
This behavior occurs when mismatched DLL files try to reference a function in Msvcrt.dll.
RESOLUTION
To resolve this issue, replace the following DLL files with new copies from a Windows NT 4.0 computer that is updated to the same service pack level and that is running the same version of Microsoft Internet Explorer as the Windows NT installation on which you experience this issue:
Msvcrt.dll
Msvcirt.dll
Msvcrt20.dll
Msvcrt40.dll
If you need more info as to resolution let me know. |
|
| Back to top |
|
|
| sadamahan |
| Posted: Sun Jul 21, 2002 1:40 pm Post subject: |
|
|
Newbie
Joined: 23 May 2002
Posts: 6
Location: Simi Valley,CA
|
HI,
You probably have both the client and the server installed on the same machine. Some MQ dlls are getting picked up from the client directory and the others from the MQM server direction. Make sure you have only c:\mqm or d:\mqm in the path.
Hope this helps.
Sada |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
