| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Performance of the message flow |
« View previous topic :: View next topic » |
| Author |
Message
|
| Mercury |
 Posted: Wed Oct 11, 2006 8:38 pm Post subject: Performance of the message flow |
 |
|
Apprentice
Joined: 24 Jun 2006
Posts: 32
Location: Hyderabad
|
Hi MBIans,
Please help me in tuning the performance of my WMB6.0(migrated from 2.1) message flows
1)I am using about 15-20 Environment variables accross the message flow
I just want to know, whether setting reference to Environment variables will increase the performance
for eg:
SET Enviroment.Variables.ApplicationId=INREF.APPID
changing this by creating reference
Declare ENV reference to Environment.Variables
SET ENV.ApplicationId=INREF.APPID
whether using such reference, will increase the performance of the flow
2)Whether using Mapping node instead of compute node for mapping will increase the performance of the flow
Please reply
thanks in advance  |
|
| Back to top |
|
 |
| elvis_gn |
| Posted: Wed Oct 11, 2006 9:00 pm Post subject: Re: Performance of the message flow |
|
|
Padawan
Joined: 08 Oct 2004
Posts: 1905
Location: Dubai
|
Hi Merecury,
| Merecury wrote: |
I just want to know, whether setting reference to Environment variables will increase the performance
for eg:
SET Enviroment.Variables.ApplicationId=INREF.APPID
changing this by creating reference
Declare ENV reference to Environment.Variables
SET ENV.ApplicationId=INREF.APPID
whether using such reference, will increase the performance of the flow |
Use references where you have a complex tree and you are planning to map, say atleast 3 or more elements deep inside the tree structure....references improve performance, but such small ones as u have used will display a very minimal time difference, or none...
I personally don't see the sense in creating a reference to map only one field with that reference...the time taken to create that reference itself could have been used for mapping....not sure, but my thinking is so...
| Merecury wrote: |
| 2)Whether using Mapping node instead of compute node for mapping will increase the performance of the flow |
A mapping node will write esql for you in the backend....you could say it will improve performance as the esql will be of good standards and performance based...but then that too will depend on how good/bad you are at coding and will have to tested to see if it improves anything...
You'll find a lot of topics on the same line, perhaps you should go through them too.
Regards. |
|
| Back to top |
|
|
| Mercury |
| Posted: Wed Oct 11, 2006 9:14 pm Post subject: Re: Performance of the message flow |
|
|
Apprentice
Joined: 24 Jun 2006
Posts: 32
Location: Hyderabad
|
| Thank you elvis_gn for the reply |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Thu Oct 12, 2006 3:04 am Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20768
Location: LI,NY
|
If your esql mapping is well done and uses references to avoid walking the tree each time stay with it.
We have seen a 20% time gain over the mapping node that way. I figure it is mostly because the mapping node maps each element from the top of the tree... And then there are the little things that are quite difficult to map...and go way easier in esql...
Enjoy 
_________________
MQ & Broker admin |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
