| Author |
Message
|
| catwood2 |
 Posted: Tue Mar 02, 2004 2:14 pm Post subject: ConfigMgr and MRM inconsistent state |
 |
|
Centurion
Joined: 17 May 2002
Posts: 108
|
WMQI 2.1
After importing message sets (mqsiIMPXMLSchema command) and deleting others(via control center) I have lost connectivity to the ConfigMgr.
The following error in EventViewer:
( ConfigMgr ) Internal error within the Configuration Manager accessing message repository:
F:/build/S210_P/src/mrm2/mrmwebdav/gprocs.cpp, line 1455; MRM return code -1.
An internal inconsistency has been detected within the Configuration Manager code while accessing the message repository. The MRM return code -1 was detected in File F:/build/S210_P/src/mrm2/mrmwebdav/gprocs.cpp, Line 1455.
Thoughts appreciated. |
|
| Back to top |
|
 |
| kirani |
| Posted: Tue Mar 02, 2004 11:41 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Are there any errors logged into Event viewer? What CSD level you are at? Did you try re-starting the Config Mgr service?
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
| catwood2 |
| Posted: Wed Mar 03, 2004 4:47 am Post subject: |
|
|
Centurion
Joined: 17 May 2002
Posts: 108
|
Kirani-
Fix pack 06.
I recycled the configMgr using both the NT service and the command line (multiple times). I also rebooted the box for good measure. Confirmed ODBC connectivity via the control panel.
| Quote: |
The following error in EventViewer:
( ConfigMgr ) Internal error within the Configuration Manager accessing message repository:
F:/build/S210_P/src/mrm2/mrmwebdav/gprocs.cpp, line 1455; MRM return code -1.
An internal inconsistency has been detected within the Configuration Manager code while accessing the message repository. The MRM return code -1 was detected in File F:/build/S210_P/src/mrm2/mrmwebdav/gprocs.cpp, Line 1455. |
|
|
| Back to top |
|
|
| girneer |
| Posted: Thu May 13, 2004 6:01 pm Post subject: ConfigMgr Erro state |
|
|
Newbie
Joined: 13 May 2004
Posts: 7
|
I have the same problem after importing a new message set into WMQI 2.1
Is there any solution other than recreating the ConfigMgr?
Can I retain the message sets that are ok and delete (by any way) only the bad once? |
|
| Back to top |
|
|
| fschofer |
| Posted: Thu May 13, 2004 11:29 pm Post subject: |
|
|
Knight
Joined: 02 Jul 2001
Posts: 524
Location: Mainz, Germany
|
Hi,
is there anything useful in the db2diag.log ?
Have you tried exporting message sets via command line ?
Greetings
Frank |
|
| Back to top |
|
|
| girneer |
| Posted: Sun May 16, 2004 10:56 am Post subject: |
|
|
Newbie
Joined: 13 May 2004
Posts: 7
|
Nothing notable in the db2diag.log.
I had the backup messageset. I had to delete and re-create the configmgr. Is there any other way? |
|
| Back to top |
|
|
| kirani |
| Posted: Sun May 16, 2004 10:26 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Sometiems these kind of problems occurs when Someone deltes the message set and you are refering to it in your workspace. You can right-click on that messageset and select "Remove". At the most restarting the config mgr should solve this kind of problem. You don't need to delete and re-create the config mgr.
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
|
|
