| Author |
Message
|
| wilsonho3 |
 Posted: Mon Jan 26, 2004 12:09 am Post subject: Need help in MQ installation/configuration on TANDEM NSK |
 |
|
Voyager
Joined: 20 Nov 2001
Posts: 98
Location: Hong Kong
|
Hi, all
I have been working MQSeries on a lot of platforms. yet, I need to
install and configurate MQSeries in a new platform for my new task.
- TANDEM NSK. I know MQSeries product quite well. Does any one
working on TANDEM NSK (installatiion & configuration) give me some
point or factors I need to take into consideration for this platform for
MQSeries.
By the way, it is ADOPTMCA parm. supported in TANDEM NSK
Thank for you message
Wilson |
|
| Back to top |
|
 |
| mqonnet |
| Posted: Mon Jan 26, 2004 6:00 am Post subject: |
|
|
Grand Master
Joined: 18 Feb 2002
Posts: 1114
Location: Boston, Ma, Usa.
|
Installation on NSK is no different and no harder than on any other platform.
http://www-306.ibm.com/software/integration/mqfamily/library/manual01/amqpac00/amqpac00tfrm.htm
Unpak the pak file for the product. Run instmqm. Verify the spooler jobs to see if there were any errors, if there were, correct them and re-run instmqm if needed(with any changes that may be required). That's it, you are all set.
As on any other platform, you need to create a group "mqm". It is advisible that you install the product using mqm.manager userid, but is not mandatory.
Yes, Adoptmca is supported on NSK.
Hope this helps.
Cheers
Kumar |
|
| Back to top |
|
|
| bkasisch |
| Posted: Mon Jan 26, 2004 11:23 am Post subject: |
|
|
Novice
Joined: 14 Oct 2002
Posts: 16
|
Kumar covered most of the major points very well. Some other considerations:
If you are not familiar with Tandem, you should review the crtmqm parameters with
some who is.
If you want to access the Tandem based Queue Manager from external tools make sure
you start the command server and start a listener. |
|
| Back to top |
|
|
| hankknowles |
| Posted: Tue Jan 27, 2004 6:03 am Post subject: Also lookup |
|
|
Centurion
Joined: 18 Aug 2003
Posts: 114
|
| If the systems are running RDF (replication) Add the PARAM MQRDF "ON" to the pathway servers etc. I learned the hard way! |
|
| Back to top |
|
|
| mqonnet |
| Posted: Tue Jan 27, 2004 6:15 am Post subject: |
|
|
Grand Master
Joined: 18 Feb 2002
Posts: 1114
Location: Boston, Ma, Usa.
|
Hank, Sorry that you had to face issues with RDF. But this param is clearly documented in the SAG in Appendix C.
Cheers
Kumar |
|
| Back to top |
|
|
| hankknowles |
| Posted: Tue Jan 27, 2004 6:21 am Post subject: Your correct |
|
|
Centurion
Joined: 18 Aug 2003
Posts: 114
|
I just failed to read further in the docs which as they say around here "MY BAD" and my error was pointed out here and saved me a few hairs... HA HA  |
|
| Back to top |
|
|
| wilsonho3 |
| Posted: Tue Jan 27, 2004 7:21 pm Post subject: Thank you |
|
|
Voyager
Joined: 20 Nov 2001
Posts: 98
Location: Hong Kong
|
Hi, all
Thank you for answers from all you guys. I will go to the Tandem
site shortly. perhaps I need some more help from yours
Thank you very much
wilson |
|
| Back to top |
|
|
| bkasisch |
| Posted: Tue Feb 03, 2004 10:34 am Post subject: |
|
|
Novice
Joined: 14 Oct 2002
Posts: 16
|
| No response from Wilsonho? Wonder if he is still at the Tandem Site. |
|
| Back to top |
|
|
|
|
