| Author |
Message
|
| jeevan |
 Posted: Tue Jun 10, 2008 3:27 pm Post subject: AMQCLCHL.TAB file is not created(RESOLVED) |
 |
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
When I created a client connection, it does not create a AMQCLCHL.TAB file.
I think( I have not used much so not sure for 100%), the file is created when the sytem is installed even without us creating any client coonnection, but it is not there and when I created a client connection, I was not created either.
I checked it under
c:\program files\ibm\mqseries\qmgrs\QMGR1\@ipcc direectory.
There is no any error on error log and no fdcs. Any clue?
Last edited by jeevan on Wed Jun 11, 2008 2:58 pm; edited 1 time in total |
|
| Back to top |
|
 |
| bruce2359 |
| Posted: Tue Jun 10, 2008 6:24 pm Post subject: |
|
|
Poobah
Joined: 05 Jan 2008
Posts: 9486
Location: US: west coast, almost. Otherwise, enroute.
|
| Quote: |
| When I created a client connection |
The mqsc command completed successfully? you didn't do the runmqsc -v option, did you?
_________________
I like deadlines. I like to wave as they pass by.
ב''ה
Lex Orandi, Lex Credendi, Lex Vivendi. As we Worship, So we Believe, So we Live. |
|
| Back to top |
|
|
| jeevan |
| Posted: Tue Jun 10, 2008 9:25 pm Post subject: |
|
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
| bruce2359 wrote: |
| Quote: |
| When I created a client connection |
The mqsc command completed successfully? you didn't do the runmqsc -v option, did you? |
In fact, I used MQexplorer in order to creat the channel. I just do usual method. The thing I wonder is why the channel table is not there. I recreated the queue manager but still the same.
No error in log and no FDCs.
Thanks |
|
| Back to top |
|
|
| vinbud117 |
| Posted: Wed Jun 11, 2008 2:29 am Post subject: |
|
|
Acolyte
Joined: 22 Jul 2005
Posts: 61
|
| Just to make sure MQ is writing to the said location search the regedit for "QMGR1" and check the prefix field. I don't see anything else going wrong. |
|
| Back to top |
|
|
| exerk |
| Posted: Wed Jun 11, 2008 4:30 am Post subject: |
|
|
Jedi Council
Joined: 02 Nov 2006
Posts: 6339
|
Are the CHLTAB and CHLLIB variables set? If so, take them out and try again. I've seen this happen where they were set and the *.TAB file deleted; it stopped the recreation of the file.
_________________
It's puzzling, I don't think I've ever seen anything quite like this before...and it's hard to soar like an eagle when you're surrounded by turkeys. |
|
| Back to top |
|
|
| bruce2359 |
| Posted: Wed Jun 11, 2008 4:36 am Post subject: |
|
|
Poobah
Joined: 05 Jan 2008
Posts: 9486
Location: US: west coast, almost. Otherwise, enroute.
|
|
| Back to top |
|
|
| jeevan |
| Posted: Wed Jun 11, 2008 7:50 am Post subject: |
|
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
| exerk wrote: |
| Are the CHLTAB and CHLLIB variables set? If so, take them out and try again. I've seen this happen where they were set and the *.TAB file deleted; it stopped the recreation of the file. |
No. However, I realised that there is some problem in my system. So, I am going to uninstall and install the MQ. I will see what happens after that and will post the result.
Thanks for suggestion |
|
| Back to top |
|
|
| jeevan |
| Posted: Wed Jun 11, 2008 2:57 pm Post subject: |
|
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
| jeevan wrote: |
| exerk wrote: |
| Are the CHLTAB and CHLLIB variables set? If so, take them out and try again. I've seen this happen where they were set and the *.TAB file deleted; it stopped the recreation of the file. |
No. However, I realised that there is some problem in my system. So, I am going to uninstall and install the MQ. I will see what happens after that and will post the result.
Thanks for suggestion |
Once I uninstall, remove all the directories and reinstalled the MQ and fp, when I created a queue manager, the channel table has been created.
Thanks you all your input |
|
| Back to top |
|
|
|
|
