| Author |
Message |
 Topic: Cert update on MQ 7.1 |
yanaK
Replies: 1
Views: 5941
|
 Forum: IBM MQ Security Posted: Wed Oct 07, 2020 4:52 pm Subject: Cert update on MQ 7.1 |
Hi
I am trying to update ssl cert for MQ 7.1 (I am on RHEL 5). I am following the steps https://www.ibm.com/support/knowledgecenter/SSFKSJ_7.5.0/com.ibm.mq.sec.doc/q012780_.htm
When I try to run
... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Wed Jul 15, 2020 7:51 am Subject: strmqm leading to STATUS(Ending preemptively) |
| Thanks Morag. I'll reach out to them. |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 11:50 pm Subject: strmqm leading to STATUS(Ending preemptively) |
I am trying to use dmpmqcfg to backup but I get:
AMQ8146: WebSphere MQ queue manager not available |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 10:48 pm Subject: strmqm leading to STATUS(Ending preemptively) |
Can it so happen that the destination queue had so much load that the source qm (this one) crashed (and not starting up)?
I see 3 of the qlocals in the destination queue has over 50k curdepth.
I' ... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 10:44 pm Subject: strmqm leading to STATUS(Ending preemptively) |
| I didn't delete it yet. No I didn't save any config - can you point me to a doc to do that? |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 10:35 pm Subject: strmqm leading to STATUS(Ending preemptively) |
| Of course, if you don't care about the queue manager you could just delete it and start again (and then tell the rest of the cluster to forget about it as well since you wont' be able to take it out t ... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 10:18 pm Subject: strmqm leading to STATUS(Ending preemptively) |
It used to work a day back! I know it's a full repository queue manager and the cluster (it has 2 full repo am and 2 normal queues) was load tested 2 days back.
Is there any fix that I can try? (Th ... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 10:01 pm Subject: strmqm leading to STATUS(Ending preemptively) |
+-----------------------------------------------------------------------------+
| |
| WebSphere MQ First Failure Sympt ... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 9:41 pm Subject: strmqm leading to STATUS(Ending preemptively) |
AMQ3884.0.FDC 2020/07/14 19:04:45.794783-7 Installation1 amqrrmfa 3884 1 XC130004 xehExceptionHandler STOP OK
AMQ3850.0.FDC 2020/07/14 19:0 ... |
| Topic: strmqm leading to STATUS(Ending preemptively) |
yanaK
Replies: 16
Views: 15747
|
Forum: General IBM MQ Support Posted: Tue Jul 14, 2020 6:42 pm Subject: strmqm leading to STATUS(Ending preemptively) |
Hi
I am trying to start my queue manager and within few seconds seeing STATUS(Ending preemptively) and then it ends. I see this in the AMQERR01.LOG:
07/14/2020 07:07:38 PM - Process(5683.1) Use ... |
| Topic: 2035 while trying to load test using JMeter |
yanaK
Replies: 55
Views: 54342
|
Forum: General Discussion Posted: Tue Jun 23, 2020 4:59 pm Subject: 2035 while trying to load test using JMeter |
all the user id settings in both setups
You mean the output of ENTAUTH command for myuser id on the QMgr and the Q (vs psqr)?
Sounds like JMeter wasn't even trying the connection when you had a ... |
| Topic: xcsCreateThread error |
yanaK
Replies: 53
Views: 39657
|
Forum: General Discussion Posted: Tue Jun 23, 2020 12:54 pm Subject: xcsCreateThread error |
What does that error mean? And I am running bash - hence the confusion.
@ PeterPotkay Do you know what was the root cause behind nofile limits being exceeded? |
| Topic: 2035 while trying to load test using JMeter |
yanaK
Replies: 55
Views: 54342
|
Forum: General Discussion Posted: Mon Jun 22, 2020 10:47 pm Subject: 2035 while trying to load test using JMeter |
Setting mq_use_mqcsp_authentication to false worked!
Thank you so much!
Still a couple of questions remain in my mind -
1. Why is MQ treating connection from my mac as psqr while from local ... |
| Topic: 2035 while trying to load test using JMeter |
yanaK
Replies: 55
Views: 54342
|
Forum: General Discussion Posted: Sun Jun 21, 2020 10:12 pm Subject: 2035 while trying to load test using JMeter |
Thanks all.
@bruce2359 I tried to put it in another queue too.
So I setup a debugger on the OS (where MQ is) and found the code is complaining about MQ_USE_MQCSP_AUTHENTICATION being null. (which ... |
| Topic: xcsCreateThread error |
yanaK
Replies: 53
Views: 39657
|
Forum: General Discussion Posted: Sun Jun 21, 2020 7:50 am Subject: xcsCreateThread error |
An interesting thing happened here - today when I went in and ran mqconfig I see this warning:
$ mqconfig
ksh bgnice:on IBM:off WARN
... |
